包头 - 商盟推荐
您好,欢迎访问!
首页 > 机械及工业制品 > 资讯正文

关于“机器人抓手图片”的相关推荐正文

包头机器人抓手图片服务至上「吉玛泰克」

来源:吉玛泰克 更新时间:2025-02-25 17:50:40

以下是包头机器人抓手图片服务至上「吉玛泰克」的详细介绍内容:

包头机器人抓手图片服务至上「吉玛泰克」 [吉玛泰克)]"内容:

双钳口自动对准平行i气动钳夹 (PE系列)

• 双动作(PE-25和PE-45可按要求单动作)。

• 高i性能,高可靠性。

• 不同行程的多种选择。

• 在整个行程中,夹紧力是不变的。

• 合金结构实现它的轻重量。

• FDA-H1 食品级润滑脂。

2-jaw parallel self-centering pneumatic gripper

(series PE)

• Double acting (single acting upon request for PE-25...

and PE-45...).

• High efficiency and reliability due to the lack of driving parts.

• Wide choice of stroke length options.

• The gripping force is constant on both directions along total

stroke.

• Light weight; due to its alloy construction.

• FDA-H1 food-grade grease.

自动校准中心气动针状夹具 PT

• 4根(PT25)或者8根(PT28)直径2mm的针。

• 适合塑料、纺织或食品工业。

• 双动作。

• 瞬时调整针行程 (1)。

• 多个安装附件 (2)。

• PT25: 大通孔 (3)。

• PT28: 用于清洁和释放的排放口 (T)。

• PT28: 用于接触热表面的PTFE 垫 (4) 。

• PT28: 选装磁性传感器 (5)。

Self-centering pneumatic needle gripper series PT

• 4 needles (PT25) or 8 needles (PT28) with 2mm diameter.

• Suitable for p1astics, textile and food industry.

• Double acting.

• Needle simultaneous stroke adjustment (1).

• Several mounting accessories (2).

• PT25: Large through hole (3).

• PT28: Blow-off port (T) for cleaning and releasing.

• PT28: Pad in PTFE (4) for hot surface contact.

• PT28: Optional magnetic sensors (5).

配置和指标

•S1:实现选择输出信号的类型,PNP(P/2)或NPN(N)。

•S2:分别根据NPN或PNP选择(通过S1)实现选择内部PULLUP(PU)或PULL-DOWN(PD)电阻器。

•L1:通电时为绿色。

•L2:当常闭系列输出切换时为琥珀色(例如:全部触点打开)。

•L3:当切换常开系列时琥珀色(例如:全部触点闭合)。

•S1: enables the selection of the type of output signal, PNP(P/2) or NPN (N).

•S2: enables the selection of internal PULL-UP (PU) or PULLDOWN(PD) resistors depending on the NPN or PNP selection(via S1), respectively.

•L1: green when powered.

•L2: amber when the NC series output is switched (e.g. allcontacts open).

•L3: amber when the NO series is switched (e.g. all contactsclosed).

传感器

磁性传感器(可选) 通过活塞上的一个磁铁检测出操作位置。因此,大量的磁性材料和强烈的磁场可能会造成传感问题。

The operating position is detected by proximity magnetic sensors

(optional) through a magnet p1aced on the piston.

Therefore, avoid using the gripper in the vicinity of intense

magnetic ffelds or near a large mass of ferromagnetic material

as this may cause detection errors.

以上信息由专业从事机器人抓手图片的吉玛泰克于2025/2/25 17:50:40发布

转载请注明来源:http://baotou.mf1288.com/jmtkzdh-2844003979.html

上一条:包头铁路正面吊出租服务介绍「山西启洋机电」

下一条:包头柠檬酸钠批发免费咨询「在线咨询」

文章为作者独立观点,不代表如意分类信息网立场。转载此文章须经作者同意,并附上出处及文章链接。
吉玛泰克自动化工程(常熟)有限公司
主营:机械手前端治具,真空系列,传感器,机电一体化组件

本页面所展示的信息由企业自行提供,内容的真实性、准确性和合法性由发布企业负责如意分类信息网对此不承担直接责任及连带责任。

本网部分内容转载自其他媒体,目的在于传递更多信息,并不代表本网赞同其观点或证实其内容的真实性。不承担此类 作品侵权行为的直接责任及连带责任。